- 08-10PP Melt Blown Filter Cartridg
- 15-09Liquid Filter Bags
- 15-09Glass Fiber Membrane Pleated
- 15-09PP Membrane Pleated Filter Ca
- 15-09String Wound Filter Cartridge
- 15-09Absolute Rate Melt Blown Filt
- 15-09Carbon Block Filter Cartridge
- 15-09High Flow Rate Pleated Filter
- 15-09Silver Sentinel Filters
- 15-09String Wound Carbon Compound
PP Melt Blown Filter Cartridges
PP Melt Blown Filter Cartridges
Description
Hongtek PP Melt Blown Filter Cartridge is made of 100% PP fibre ,manufactured by different pore diameter of spray nozzles.depth construction with fine fibers in inner layer when in outer layer fiber is coarse .It is high dirt holding capacity,low pressure drop,high flow rate ,good chemical resistance, no fibre release ,longer service life and effectively filtration for suspended particle,sediment and other kinds of impurities .
Feature
1, Safety Polypropylene material have a lot of demanding applications .
2, Depth layers structure ,high contaminant holding capacity and longer filter service life .
3, Made of FDA grade PP material which is environmental protection ,without binders,additives and lubricants .
4, High filtration efficiency,consistent filtering performance
5, Mainly applied to most industry standard housings .
Application
1,Industrial waste water treatment 2,Plating solution
3,Pre RO/ID water filtration 4,Chenmicals and Solvents
5,PCB industry 6,Electronic Industry
7,Petrochemical Process 8,Food & Beverage
Specifications
|
Filter Media |
Polypropylene |
|
Length |
5",9.75"9.8",10",20",30",40",50" ,60" |
|
Micron Rating |
1, 5, 10, 20,30, 50, 75, 100 μm |
|
Inside Diameter |
0.8"(20mm), 0.9"(23mm), 1"(26mm), |
|
Outside Diameter |
2.36"(60mm),2.4"(61mm), 2.5"(63mm), 2.55"(65mm) |
|
Core |
PP |
|
Gasket/O-ring |
Silicone, EPDM, Viton, Teflon encapsulated Viton |
|
End Cap |
Flat ,222 O-Ring,226 O-Ring,Fin |
Operation Data
|
Max. Operating Temperature |
60 ℃(140℉) |
|
Max. Differential Pressure |
3.0 bar at 27℃ (43 psi at 80℉) |
|
Recommended Change Out Differential Pressure : |
1 bar (14 psi) |
Order Information
Normal type : HT-D-M-Rating-Length
|
HTPP |
ID |
OD |
Rating |
Core |
Length |
End Cap Type |
Seal material |
|
Hongtek PP Melt Blown Filter Cartridge |
A:20mm |
J:60mm |
01:1μm |
W:With Core |
5: 5" |
Ⅰ-222/Flat end |
V:Viton |
|
B:23mm |
K:61mm |
05:5μm |
N:Without Core |
9.75:9.75" |
Ⅱ-222/Fin |
S: Silicon |
|
|
C:26mm |
M:63mm |
010:10μm |
|
9.8:9.8" |
Ⅲ-226/Flat end |
E:EPDM |
|
|
D:28mm |
Y:65mm |
020:20μm |
|
10:10" |
Ⅳ-226/Fin |
B:NBR |
|
|
E:30mm |
|
030:30μm |
|
20:20" |
|
|
|
|
F:33mm |
|
050:50μm |
|
30:30" |
|
|
|
|
|
|
075:75μm |
|
40:40" |
|
|
|
|
|
|
100:100μm |
|
50:50" |
|
|
|
|
|
|
|
|
60: 60" |
|
|
|
|
Other Customized Sizes |
|
|
|
|
|||
For Example:
HTPP-E-M-01-N--01-10-Ⅰ-S
PP,ID:30mm, OD:63mm, Rating:1μm ,Core:Without Core,Length:10",End Cap:222/Flat end, Seal:Silicon
Download