PFG Series Pleated High Flow Cartridge Filters are Paker Fulflo MgaFlow high flow cartridges replacement, cost effective alternative to large flow filtration system. OD 6inch(152mm) pleated high flow cartridge equal to 8 standard 2.5inch OD x 40inch long depth filter cartridges. High flow rate reduce the number of cartridges required and allows for smaller housings, and widely used in high flow applications, such as reverse osmosis pre-filtration, where need good filtration effect. Positive O-ring seals and a convenient built-in handle make high flow cartridge filters installation reliable, fast and easy.
| Filter Media | Polypropylene Pleated |
| Length | 40"(1016mm) |
| Outside Diameter | 6 inch(152mm) |
| Filtration Rating | 0.5μm, 1μm, 5μm, 10μm |
| Support/Drainage | Polypropylene (PP) |
| End Cap Material | Polypropylene (PP) |
| Seal Material | EPDM, Buna-N, Viton, Silicone |
| Outside | Netting |
● Cost effective alternative to large flow filtration system to protect UF & RO membrane
● The good quality of high flow cartridge filters is equal to Paker Fulflo MgaFlow high flow cartridges
● High surface area pleated design of high flow cartridge provides lower pressure drop and longer service life
● High flow capacity of pleated high flow cartridge means fewer cartridges & change-outs which reduces labor costs
● High flow cartridge filters are available in pleated polypropylene media with nominal ratings of 0.5, 1, 5 & 10 micron
● Good performance with consistent good filtration efficiency and wide chemical compatibility for different applications
● Waste water
● Potable water
● RO pre-filtration
● Chemical industry
● Power generation
● Food and beverage
● Sea water desalination
| Maximum Operating Temperature | 90℃ |
| Change Out Differential Pressure | 35psid (2.4bar) |
| Suggested Maximum Flow Rate | 175gpm (662lpm) |
| Maximum Differential Pressure | 150psid (10bar) |
| Filtration Surface Area | 5 - 5.5㎡ |
| Liquid Flow Direction | Outside to inside |
Filtration Efficiency
| Length of Cartridge | Rating | Media | Removal Rating (μm) @ Efficiency of | ||||
| 90% | 95% | 98% | 99% | 99.90% | |||
| 40"(1010mm) | 0.5μm | PP | 0.5 | 1 | 5 | 10 | 20 |
| 1μm | 1 | 5 | 10 | 20 | 40 | ||
| 5μm | 5 | 10 | 20 | 30 | 50 | ||
| 10μm | 10 | 25 | 60 | 70 | 80 | ||
Drawing for PFG Series Pleated High Flow Cartridge Filters
| PFG | Material | Length | Filtration Rating | Open End Type | O-ring Material |
PFG Series Pleated High Flow Cartridge Filters | P = PP Pleated | 40 = 40"(1016mm) | 0.5 = 0.5μm | S = Single O-ring | E = EPDM |
| 1 = 1μm | B = Buna-N | ||||
| 5 = 5μm | V = Viton | ||||
| 10 = 10μm | C = Silicone |
For Example:
PFG-P-40-5-S-E
PFG Series Pleated High Flow Cartridge Filters - PP Pleated - 40" - 5μm - Single O-ring - EPDM
Hongtek Filtration Co., Ltd.
Copyright © Hongtek Filtration Co., Ltd. All Rights Reserved | Sitemap
